Posts

Chosen Solution How do I get my amazan 10 IMEI number for this tablete Update (02/19/2022) I’m trying to get free Qlink WiFi service hooked up to my amazanan kind fire 10 tablet If I’m not mistaken, the IMEI (International Mobile Equipment Identity) number are assigned to mobile cellphones. Your tablet, if it isn’t a cellular device, won’t have an IMEI number. You can find related info in settings and status tabs whether in your cellphone or tablet....

Chosen Solution Hi, I was wondering if it’s possible to completely remove the emmc from this model. Thank you! Hi, According to the hardware maintenance manual for the laptop it has a removable M.2 2280 type SSD card for data storage and not hard mounted eMMC storage. If you wish to remove it go to p.41 in the manual to view the procedure. How do you intend to use the laptop without a storage drive i....

Chosen Solution I just need to figure out how to replace the glass on my phone. I dont need a new LCD just the glass I had the same question, but after watching this video realized it is much much easier to replace the entire lcd display instead of just the glass. Samsung Galaxy J3 (2016) Screen / Glass Replacement

Chosen Solution My Casio Casitone CT-S100 keyboard’s USB Micro-USB port came out. How do i repair it? that would be a re solder jobbie they are fairly generic iv changed a few in the past usually four solder points, easiest to remove with a hot air gun, you’d have to take the board out put some flux on the old port, heat it up with the hot air gun and lift it with some tweezers (if it doesn’t come away add some fresh solder and try again), then clean the pads up with your soldering iron, position you’re new one on top taking care to line the pins up and re-melt the solder, add a little more and then make sure that there are no bridges if you type into youtube micro usb replace you’ll see what i mean, not too hard but watch a video and make your own mind up

Chosen Solution I tried putting upward pressure on the screen and the screw still spins (this was the answer in another post on the topic Pentalobe screws just spinning!). I’ve tried using gravity as I unscrew it. I’ve tried pushing the screen toward the back. I’ve pried the side without the screw up. I tried finding something sticky to put on the driver, like putty, but to no avail. I’ve even, hold on to your shorts, put some superglue on the tip of the driver to pull it out....

Chosen Solution My RCA tablet has been locked by the bogus FBI banner. Can’t find a way to delete the banner @rfkeith10 sounds like your tablet is being held hostage by ransomware. I am sure that is says somewhere on your screen that if you pay some money to some account, it will get released. You will have to to boot the tablet into safe mode and uninstall it from there....

Chosen Solution Hey guys, I have the typical bent iPhone problem. Is there a way to safely bend it back. Apple will replace it for free but I have it jail broken and would rather go back to android if I can’t have a JB iPhone. And if they replace it, it wil come with 8.3 and I won’t be able to jailbreak it. So can I bend it back safely ?...

Chosen Solution hello friends, i got an iphone 6 16GB. It shows the Itunes Sign. When i try to restore i always get itunes error 9. Before it worked great. I didn’t drop it nothing, i just wanted to do an update and this happens. i tried i4tools but it stays at 20 % “Nor Data”. One time it went to 80 per cent but then crashed. i spent more than 4 hours on it but didn’t find any solution....

Chosen Solution Hello. Pls, somebody help me. I can’t start my small printing biz because my HP desk jet advantage 2010 printer won’t turn on. No lights on power button. Just this red exclamation on paper symbol. My last used was printing shrink film( basically letter sized and likely photo paper type. Now the sized of the film is not whole letter. It’s half already bcuz I cut some on my previous prints and I did print the remains cut to save films....

Chosen Solution I have a Keurig K-Elite, it does not look like the picture, but this is the model I have (https://www.amazon.com/Keurig-K-Elite-St…) and no matter what, I can not get it to brew over 8 oz. The K Elite has five cup sizes, the 10 oz, and 12 oz will only ever brew 8 oz. I have cleaned descaled, done all kinds of things to fix it. I wonder is there is a part that I could replace like the air pump that would fix this, or is it a circuit board problem....

Chosen Solution My MacBook Pro 13” from 2018 got water within the display layers. Is it possible to open the display lid? Is there any other idea how to remove the water? everything else - including keyboard - works fine. The body seems to be coffee and water resistant. Only the display light is little uneven shining. Unlike Dan, I love delivering bad news. Since the retina variant, I have never seen anyone managed to take the LCD off intact....

Chosen Solution How do I replace the cloudy water in my snow globe with clear water? Hi, It might depend on how your snow globe is constructed but here’s a video that may help. There are a lot more to look at if the first video didn’t help.

Chosen Solution I have had this TV for 6 years with No issues. Since about 2 weeks ago when I watch non-HD channels via STB or Wireless the Screen randomly freezes, then goes blank, shows LG screen, and returns, works normally for few minutes till repeats. When I watch HD channels via STB or wireless, It has no issue even if used for few hours. I tried a reset to the initial setting and that did not help....

Chosen Solution I have a htc one m7 and it just started doing the reboot loop everyone is talking about. I think it is completely died, but the green light notification is blinking slowly. When i plugged it up to the wall an orange light starts blinking while the green light is still on. it shows the battery icon with the lightening bolt in the middle but it just start rebooting again....

Chosen Solution Thanks Alot. I’d like to buy exactly this hard disk but I can’t find it on the internet. I want to change the hard disk board cause I want to safe the datas and I didn’t made any backup. I know… stupid. The days of a raw PCB swap died with the mid 2000’s Maxtor DiamondCrash* drives after they were discontinued :-(. You need to transfer the ROM on these newer drives, and make sure your donor is a 100% match....

Chosen Solution Harman Kardon go play speaker. Works when plugged in but won’t charge. The first light of power goes on and off when plugged in, when I remove cable speaker turns off. This problem is about nmofset transistor. Product number is ME 4894-G But i didn’t find it anywhere

Chosen Solution blower motor works fine with key on accessory position but only works low speed with engine running mikephillips1948 possibly a bad resistor pack. You can never totally rule out the switch, the motor itself or the wiring. It will help if you tell us what model and year your Vehicle is.

Chosen Solution Please fix my ipod…I’m so heartbroken. Can I send it to you??? Hello! I’m sorry to hear about your broken iPod. Unfortunately, iFixit does not offer repair services—instead, we’re here to encourage people to repair their own devices! I encourage you to check out our iPod repair guides. I’ll also move your question over to our Answers forum, where someone may be to able to offer you some repair advice....

Chosen Solution I replaced the screen on my first iPad Air ever. Before closing it up I did the usual QA check. And after closing it up I did it again. All was well on my bench. Two days later the customer contacts me to tell me that the home button was sunkin and sticking. Sure enough when he brings it back to me, it’s sunk. I removed the screen and compared it to the old one (which thankfully I had not tossed yet) and there was a missing cushion....

Chosen Solution My computer has a touchpad that rarely works, is slow, overheats instead of going to sleep 50% of the time, and disconnects from WiFi frequently. HELP ME BE FREE BEFORE I BREAK THIS PIECE OF CRAP!!!! I have a better laptop, but it’s too distracting. @luigiytp, if you’re not wanting to replace/recycle your current machine; my best advice for your issues is to watch a repair guide on re-applying the thermal paste on your heatsink, as well as making sure you maintain a clean and clear path for the fans to exhaust....