Posts

Chosen Solution How doI replace damaged wheel on my walker? I don’t know what the specific walker.But often things with hard plastic wheels use standard ball barrings that’s also used on skateboards, rollerskates and scooters.A good place to buy new bearings is a skate shop, since they will usually be in the correct size, and of good quality. The hardest part is getting the old bearings out. Heres a guide for doing it on roller skates but if you look at method 3, that should be applicable to all things using similar bearings

Chosen Solution The USB ground/mounting sheath broke loose tonight when my phone fell off the seat while I was turning and tugged on it. I figured it would be an easy fix, but since this was $250 or so, I wanted to be sure I’d get it right. How does one go about fixing something like this that needs to hold up to abuse? The middle piece was a bit loose also, but I already touched up the soldering on those points....

Chosen Solution Hello all, I’m currently facing an issue with my phone and have done numerous troubleshoots to try to diagnose the issue. Long story short, my phone suddenly died on me one day at 50% battery life and would not turn back on; couldn’t boot into Recovery, Download, etc; absolutely no response. I looked at xda threads with this issue like this one: https://forum.xda-developers.com/s7-…t… and followed their recommendation to let the battery completely drain over a few days, recharge to full capacity, and attempt to boot again....

Chosen Solution Hey, I ordered a new replacement screen for my z3c. Yet, on replacing it I realised that the digitizer cable keeps getting loose from its socket (?). Thus, while the screen itself functions, it is unresponsive to touch (of course, since the cable does not stay attached to the socket. Any ideas ? I have my old screen that is responsive to touch but has a broken lcd - can I somehow use its digitizer on my new screen?...

Chosen Solution My phone(O+ 8.38z android) has got lot of horizontal thin lines and it was moving up and down on my screen how to fix it @francejay this “lot of horizontal thin lines and it was moving up and down” sounds like a broken display. you do want to post some images of what your screen shows with your question. That will allow us to see what you see. Use this guide Adding images to an existing question for that....

Chosen Solution My ZTE will not charge at all and I know it has something to do with the charger port does anyone know how to fix this problem? Or does anyone know someone who can fix it for me? Also I live in the 559 area. My ZTE phone is a month old and about a week ago everytime i would try to charge it , it would send me a message saying my charger was week along the lockscreen....

Chosen Solution Cannot recharge tablet because cord doesn’t stay in on tablet. How can I fix this as the area seems loose. It depends on the extent of the damage to the charge port. You may be able to squeeze the metal surrounding it back together with a pair of pliers if the port is otherwise undamaged. This would require you to remove the back casing.If the port is damaged it may need to be replaced....

Chosen Solution When I try to turn it on , the LED flashes white one time and when I continue pressing the button it flashes blue. I would like to know how to fix or atleast reset it to factory settings. Thank you for jbl e25bt I believe that the blue light you’re seeing is the device trying to establish a bluetooth connection. Verify the device you’re connecting to has bluetooth enabled and if you are still having issues it might be due to an issue internal to the E25BT....

Chosen Solution 4-6 keys are not working. Every other button on the calculator works though. Cant If there is a way you would have to open it and remove plastic rivets (Cant) then repair buttons

Chosen Solution My shutter button does not work well anymore: it takes a picture when fully pressed, but it does not make focus when half-pressed anymore. I know it is not a configuration issue, everything is double checked on this side, so it’s a hardware issue. I’m trying to tear it down, but once I removed the back side of the camera, I don’t manage to reach the shutter button to see what’s wrong… Here is what i did already: E-pl5 teardown I’m stuck after that… Does anyone already did it and know how to do it step by step ?...

Chosen Solution Screen has charging icon with about 10% red. Charging cord has green light on. Doesn’t respond. My hunch is that the battery is in poor condition. I would recommend downloading coconutBattery and checking the percentage of the design capacity, the status, and the cycle count. If the percentage of the design capacity is less than 80% or the cycle count is greater than 1000 or the status says “Poor” then you may have a bad battery....

Chosen Solution New battery, horn, signals, brakes lights work. Headlights and staeter, no response. wolfgreimann you forgot to tell us what you have checked and what the outcome of those checks were. Here are the wiring diagrams for your scooter including the starting system. Please remember that If the main switch is set to “ON” (switch is closed), the starter motor can only operate if at least one of the following conditions is met: The sidestand switch is up (the side stand switch is closed), and the brake lever ( front or rear) is pulled to the handlebar (the brake light switch is closed) This means that you have to make sure you check all of those switches as well...

Chosen Solution Hey guys, I have a motherboard that gas been running for 2+ years and my headphone jack snapped off and got lodged inside the rear audio output of my motherboard. My stupid self tried to drill out the jack but instead broke the port itself. Is there any way I can replace it? I have the necessary tools to do so. The jack is made by lotus if you were wondering....

Chosen Solution hello, i have a problem in my Computer.this problem is that it heats up and turns off suddenly.please help me Is the laptop turning on every time and displaying the picture then getting so far and then shutting down? If so the board may just need reflowing and you can do the job with a hot air gun on medium this is reflowing, for reflowing the you need to bring the componants up to about 230 to 250 degree’s in order to reach reflow temp so that the solder holding the componants is resoldered and not cracked as this is more than likely the problem but firstly try this....

Chosen Solution Hi all, was wondering if I could get some help with my Hisense 49” Smart TV. The backlight went on it a week ago so I opened it up to see if I could work out where the problem was coming from. I noticed there was a burnt out area on the circuit board around a component that I identified as a Zener Diode (pics attached). I am hoping to fix it rather than buy a new TV, but I didn’t know whether it burnt out due to some other problem with the TV or due to the component itself malfunctioning....

Chosen Solution Hi, I have hp elitebook 820 g2 laptop. Its battery doesn’t charge with adapter. I tried different ways. I bought new adapter also bought new battery but the problem is still there. When I pluged in adapter then I can use the laptop. Battery is not charged. So please advise me is this charging port issue ? If so can I buy new charging port to fix it ?...

Chosen Solution I bought used iPhone 4 with dead battery, I changed it. Then I was greated with passcode screen, previous owner told me some codes that can be correct. But they all ended up being wrong. iPhone locked it self and now asks about iTunes. I told that previous owner, he deleted it on he’s iCloud page. Now I just need to connect it to the internet and it will wipe it self....

Chosen Solution need to disassemble a Canon mx 922 printer This bing(!) video should do the trick: https://www.bing.com/videos/search?q=rep… I followed it after I got an error code indicating that the print head was bad; the print head was EASY to remove—no tools—but replacement ones are expensive & somebody suggested it could be a problem w a fuse on the logic board, so I opened up the side to visually inspect where the printhead cables attach....

Chosen Solution I have tried everything and nothing works, still says it needs more space. It’s a 32GB anything will help please and thank you. Sorry, I didn’t realize that other’s may be having the same issue. To sum it up, I downloaded Windows Media Creation Tool at a 64-bit operating system, I also downloaded the software and driver packages from the manu. website, I would recommend only download the driver package because the OS is useless....

Chosen Solution The wires from the button battery to the board have come lose. They were “soldered” on. Can I melt the solder with a soldering iron, connect the wires again, and solder them back on? Or do I just replace parts? You definitely can resolder the battery to the board, but you need to remove the existing solder and use new.