Chosen Solution My speed control panel needed adjusting as my stand mixer would only go high speed no matter what setting. When I opened up the back to try adjusting the screws first to fix the speed problem a little piece fell out that is a U-shaped with a rolling metal cylinder on the bottom. It just fell out and I have no idea where it goes or if it’s essential to put back in but I’m guessing so....
Chosen Solution These symptoms can happen when the end ground pins on the touch connector get bent in too much. I have seen this several times on the iPhone 8 after numerous connecting and disconnecting of the connector. I usually pry them back out with a thin needle. I have stopped repairing home buttons but I did find this info handy from Ben Duffy. Try unplugging the home button connector all together....
Chosen Solution Following the iFixit battery replacement guide, I did a battery replacement a few months ago. After the battery replacement, my home button stopped working. It doesn’t register any presses and neither does Touch ID work. My friend was doing a screen replacement on his 6S and it came with a home button. He intended on keeping his original home button, so I had asked if I could have his spare home button....
Chosen Solution My Hoover Windtunnel 72400 hose will not snap into place anymore. This makes it extremely difficult when trying to vacuum because the handle pulls out when you pull the vacuum towards you. How do you fix this specific problem. The suction on the vacuum is fine. Make sure the button is snapping into place. Try steps 3 & 4 of this guide: Hoover Windtunnel Air Steerable Upright Suction Hose Replacement
Chosen Solution When I press the power button once, the phone displays “Turn off Mode.” After 10 seconds, the phone restarts and continues until I hold the power button or press it for some time. Its a rather simple fix. If you have a case take it off and find a hard surface and smack(use your own discretion if I have to explain the reaction of plastic hitting something hard return to your seat and continue likcking the window) the backside of phone near power button against it several times....
Chosen Solution Is there an option to replace the screen. Or is it a screen at all. Watch works fine but glass is pitted from work All i can find i is this. https://rounded.com/samsung-galaxy-gear-…
Chosen Solution My disk drive for my Lenovo laptop recently won’t work t ll. It cts like there is no power going to it at all, and won’t even open or blink if I push the button to open it. I’d like to know how to get to the drive to see if maybe its something as simple ass a disconnected wire or if the drive truly is broken. Follow this guide: Lenovo IdeaTab G50 HDD, SSD Replacement Replacement...
Chosen Solution My backspace key is wonky! It’s moving up and down (left and right motion sorta) when I type. I was trying to clean it because for some reason my when I tried to delete just one letter in between a word it’d delete the whole word or two letters instead of the individual one I wanted so I began to take it off, my laptop is an Acer and I had/have no idea if the keys are able to come up so I need serious help!...
Chosen Solution I charged my power bank for a few days but there is no sign of power. Hi Depending on the age of the power bank the battery’s can die for good and will need replacing (even lithium ones) So unless the charging port is damaged or is full of dust and debris (can be easily removed with a sewing needle)it’s probably the battery’s So my advise would be replace the battery’s and if that’s not a option sell it on eBay to someone who can fix it so it doesn’t end up in land fill and buy and new or used one Hopefully I answered your question If you have any more questions please let me know Thanks:)
Chosen Solution Mark, visible on screen and on pictures, approx 3mm long X 1mm wide. Could be something inside lens or infront of sensor. It does vary in size and sharpness depending on zoom & focus set. If I follow disassembly instructions , where is the object likely to be and can I get to it to clean? To remove the dust, you will need to remove the lens and disassemble it in a cleanroom....
Chosen Solution i would like to open nvidia shield pro to clean dust from inside….how to open up case> There are guides on ifixit, you’re just in the wrong section. Check this : Nvidia Shield Pro Android TV Repair
Chosen Solution I need to replace the volume buttons on my GS9+. Which part do I need to replace to make this happen? if the actual button are ok, the part you need is here. https://www.esourceparts.ca/samsung-gala… . follow the teach town guide to install . Samsung Galaxy S9+ Teardown
Chosen Solution my power button is broken and i want to turn on my TAB so please help !! Open the Back Plastic of the Tab, and then get some sort of tool made of conductive metal (like tweezers) and try MANUALLY shorting the two power button pads, is the same thing as pressing the button.
Chosen Solution My original Apple Watch s1 battery was expanding and pushed the screen off the body of the Watch. So I replaced it with a battery from ifixit. The watch now shows the red snake when not charging, and green snake while charging. No matter how long it charges. If I let the watch off the charger for a week or 2, and then charge it, it’ll boot up and work normally for a day....
Chosen Solution My dyson 37, still has power but there is a loss of suction, there was a substantial blockage where the hose feeds into the bottom of the catch container- I have cleaned filter and ran water into the while catch (cyclone) unit- waiting for everything to dry, I NOTICED THE TOP OF THE CYCLONE UNIT COMES OFF WITH SCREWS- I don’t hear anything in there- is it worth taking apart ?...
Chosen Solution Car won’t start rest everything get fuel spark acts like it wants to start but doesn’t 98accordv6 Wat could it be If you have connected a spark tester and you have good strong spark and you have fuel on the spark plugs so you believe you have good fuel pressure and injection then you need to verify timing, did the timing belt jump. Fuel pressure can still be too low and spark can be too weak, please use testers to verify and inspect timing belt alignment next....
Chosen Solution I have repaired my open tray error by messing with the calibration screws inside my disc drive. About 2 months later it started not reading discs again and kept saying open tray. I opened it back up and tried again accept this time i turned the screws both a few full revolutions thinking that i would find where it stops and use that as a start point for calibrating....
Chosen Solution I’m attempting to repair This iphone, it’s not crucial that its fixed but would be nice. It has an issue where it appears to have a yellow streak drawn across the sceen from the bottom left corner to the upper right, as well as the home button getting hot. Apparently the phone sat in a dry cooler for a number of hours outside and afterwards these issues were noticed, so its presumed that its due to either humidity in the cooler or from heat in the cooler....
Chosen Solution Got an 8 with a too sensitive home button, replace turtle but still its the same… any ideas why? the 7/8/SE (2nd gen) home buttons are not mechanical, like those in the 4/5/6/6s, and really don’t have a “sensitivity” that can be adjusted. that said, i have found that loosening or tightening the screw that holds the actual button to the home button display bracket can change how the button responds to a touch....
Chosen Solution When I turn on my computer it says that windows is not activated, I have tried to activate it using the internet but it doesn’t want to recognize the internet cable you can activate windows by phone: CLICK here If you can’t get it online mate try a call to Microsoft depends on what you put on ? new machine, upgrade, old machine new drive etc
