Posts

Chosen Solution So the iPhone glass has chipped away so much and their is only a piece of it left in the lower-left corner. My question is, how can I remove the front panel now without bending the whole frame. I have a suction cup but trying to suction cup the rest of the panel instead of the glass only bends it instead of lifting it up. Any suggestions? I use an iSesamo but you could use a Jimmy or some other kind of thin pry tool....

Chosen Solution i have the machine open but the shredders wont turn at all, so cannot remove the jammed card. You should be able to get into it using this guide: https://www.youtube.com/watch?v=9XeLPuuh…

Chosen Solution Some background: my laptop won’t turn on whatsoever, no power indicator lights, charging lights, nor fans turning on. The device will not turn on or retain a charge. I would like to know how to replace the battery charging port on my laptop. I had a free diagnostic done and they said that the port was physically damaged. They were not able to test if the laptop would turn on with a good battery because they didn’t have an extra....

Chosen Solution I’m having trouble reinstalling LCD touch screen connector cable, getting cable to align with port. I broke the original cable during the reinstall and had to order another one to try again. Any suggestions? Repair videos on YouTube make it look so easy but I am having trouble getting everything to align. Hi, Could you attach a photo of exactly which cable and port you are talking about? I have not had any issues with putting the cable back into the hole....

Chosen Solution I have a garage door opener. It appears to be an MSW GD-800 as per this link https://www.amazon.co.uk/MSW-GD-800M-Gar…. However it is red. Previous owner lost the remote controls. I have bought replacement Universal remotes at 315MHz and 433MHz but neither seem to be picked up by the unit when i switch it to remote learning mode. I suspect that it is some odd frequency but i don’t have an oscilloscope to determine what the receiver is....

Chosen Solution Just installed a new battery in my 5th gen. iPod video. New battery is working properly after a charge, however, each time I try to put the case halves back together it will power down and not turn on again. Any ideas as to how I can fix this? mwgibbs, Check the battery connector and flex cable damaged inpact any component missing arround battery connector Hope this guide will help you to troubleshoot the fault Check with another battery

Chosen Solution The tip of the charging cable has broken off inside the charging port. What is the easiest way to remove the broken tip? You will need to replace the dock connector, that’s the best way.

Chosen Solution I’ve purchased Galaxy S8 with broken screen - someone did factory restore (what I see from bottom of the screen - language choose) I’ve tried to connect to SmartSwitch under MacBook but I got “Failed to connect Device” I got non-brand USB C dongle with HDMI + USB full size and another USB C for power (I put there Samsung Fast Charger for extra charge) I saw on Youtube someone had the same looking dongle (but not sure if exactly) and it was working this way (dongle connected to S8 + charger to dongle + HDMI to TV + mouse to USB) BUT…… that person got…… “set up” Android already - not like me - stuck on language selection because touch screen is not working and just bottom of the screen is working (barely)....

Chosen Solution i broke my lcd display ribbon cable while replacing the screen and there r no tutorials n that If it’s the 2019 as per the listing then you’ll need another new screen.

Chosen Solution My google home mini only recognizes the command prompt but only picks up static with the microphone. Here is a recording of what it picks up. Maybe this is a bug in the software that is installed on the google home. Have you tried to update it to the latest software or firmware?

Chosen Solution Hi, I. have an 85W Magsafe 2, which had the cable damaged. As I don’t need it to power a mac, would it be possible to use it as a bench power supply? Measuring the voltage with no load, shows 3V on my multimeter. How can I make it work? I read somewhere that it needs to see 40kohm, to activate. I’ve tried to put a 40kohm resistor there and it doesn’t wake up to max voltage....

Chosen Solution Has anyone replaced the glass on a epic Learning pad, it is maybe 7 or 8 inches, Blue case, with blue rubber cover. Intel processor, Model ELT0801 16GB EPIK Learning Tab ELT0801-PK Kids Tablet Looks like you can get the digitizer repair kit here for $24: http://www.ebay.com/itm/US-New-Digitizer…

Chosen Solution Water damage to my screen on my Stylo 5 Is it repairable You’ll need to replace the screen. Here is a Youtube video that takes you step-by-step for the screen replacement. https://www.youtube.com/watch?v=F2Z55qIa…

Chosen Solution So I having the same issue, I bought a 2019 MacBook Pro 13 Inch model, which arrived yesterday morning. It was working normally but at about 56% battery it just shut itself off and it keeps doing that no matter how often I perform said SMC reset. Gonna call Apple tomorrow they better replace me my !&^#% machine … haven’t even had it for 24h and its basically junk....

Chosen Solution I have a 2015 MBP 13" Retina (A1502) which has a strange kernel_task issue and shows errors in Diagnostics —— PPN001( i don’t know what this code means) , PFM006(SMC issue), PPF003(Fan issue). I want to be able to try cleaning out the insides, especially the temp sensors. Can someone help me regarding their locations? I don’t think general cleaning will address these errors. Diagnostics finds electrical faults not general temp issues....

Chosen Solution i cant get past the home screen that says hello press home button to continue. Is there any way to bypass that ive replace home button . PHONE locks me out for a hour everytime i try Sorry just got back in. It says press home to upgrade

Chosen Solution How can I manually ope my power liftgate To manually operate the liftgate: Disable the liftgate power function. Refer to the Message center in the Instrument Cluster chapter of owners manual. Disable the power liftgate enable/disable switch about 1/2 way down the options list or so. Open and close the liftgate as you would a standard liftgate. Refer to Manual liftgate portion of the owners manual. If you don’t have the owners manual you can view an electronic one here....

Chosen Solution I have tried twisting where the unlock sign is, but it doesn’t seem to be able to come apart. I think something is keeping it from unlocking all the way. Can someone help? Unfortunately, you have to take off the clear dasher before you can completely disassemble the machine. To do this, twist the piece to the left until it comes apart from the machine. Once this is removed, you should be able to take the upper housing and lower housing apart with ease....

Chosen Solution I found a very rare .rtf document, in which the text looks pretty decent. Fortunately, there are no photos in the document, but there is text that needs to be pulled out. Some fragments of the document look unrecognizable. Because of this, I thought that it would be nice to convert rtf, at least into text or another text format. I tried to use for this Word, but different versions of Word generate different kinds of rtf....

Chosen Solution I have an iPhone 6 and its screen wont respond to touch in certain areas so I purchased a new screen and digitizer and I need to know if theres a way I can replace the components without destroying touch ID functionality. Thanks touch id is on the home button not the actual lcd, use the original home button and metal backplate and it should be fine